Spesifications CJ1W-OC / OA / OD

CJ1W-OC201 Contact Output Unit (Independent Relays, 8 Points)

Name	8-point Contact Output Unit with Terminal Block (Independent Relays)
Model	CJ1W-OC201
Max. Switching Capacity	2 A 250 VAC (cosφ = 1), 2 A 250 VAC (cosφ = 0.4), 2 A 24 VDC (16 A/Unit)
Min. Switching Capacity	1 mA 5 VDC
Relays	NY-24W-K-IE (Fujitsu Takamizawa Components, Ltd.), Cannot be replaced.
Service Life of Relay	Electrical: 150,000 operations (24 VDC, resistive load)/100,000 operations (240 VAC, cosφ  = 0.4, inductive load)  Mechanical: 20,000,000 operations  Service life will vary depending on the connected load.
ON Response Time	15 ms max.
OFF Response Time	15 ms max.
Number of Circuits	8 independent contacts
Insulation Resistance	20 MΩ between external terminals and the GR terminal (500 VDC)
Dielectric Strength	2,000 VAC between the external terminals and the GR terminal for 1 minute at a leakage  current of 10 mA max.
Internal Current  Consumption	90 mA 5 VDC max.  48 mA 24 VDC max. (6 mA × No. of ON points)
Weight	140 g max.
Circuit Configuration	The signal names of the terminals are the device variable names.  The device variable names are the names that use "Jxx" as the device name.
External connection and  terminal-device variable  diagram	The signal names of the terminals are the device variable names.  The device variable names are the names that use "Jxx" as the device name.  The input power supply polarity can be connected in either direction.

* Terminal numbers A0 to A8 and B0 to B8 are used in the external connection and terminal-device variable diagrams. 
   They are not printed on the Units. 
Note: Although 16 I/O bits (1 word) are allocated, only 8 of these can be used for external I/O.

CJ1W-OC211 Contact Output Unit (16 Points)

Name	16-point Contact Output Unit with Terminal Block
Model	CJ1W-OC211
Max. Switching Capacity	2 A 250 VAC (cosφ = 1), 2 A 250 VAC (cosφ = 0.4), 2 A 24 VDC (8 A/Unit)
Min. Switching Capacity	1 mA 5 VDC
Relays	NY-24W-K-IE (Fujitsu Takamizawa Components, Ltd.), Cannot be replaced.
Service Life of Relay	Electrical: 150,000 operations (24 VDC, resistive load)/ 100,000 operations (250 VAC,  cosφ = 0.4, inductive load)  Mechanical: 20,000,000 operations  Service life will vary depending on the connected load.
ON Response Time	15 ms max.
OFF Response Time	15 ms max.
Number of Circuits	16 points/common, 1 circuit
Insulation Resistance	20 MΩ between external terminals and the GR terminal (500 VDC)
Dielectric Strength	2,000 VAC between the external terminals and the GR terminal for 1 minute at a leakage  current of 10 mA max.
Internal Current  Consumption	110 mA 5 VDC max.  96 mA 24 VDC max. (6 mA × No. of ON points)
Weight	170 g max.
Circuit Configuration	The signal names of the terminals are the device variable names.  The device variable names are the names that use "Jxx" as the device name.
External connection and  terminal-device variable  diagram	The signal names of the terminals are the device variable names.  The device variable names are the names that use "Jxx" as the device name.

* Terminal numbers A0 to A8 and B0 to B8 are used in the external connection and terminal-device variable diagrams. 
   They are not printed on the Units.

CJ1W-OA201 Triac Output Unit (8 Points)

Name	8-point Triac Output Unit with Terminal Block
Model	CJ1W-OA201
Max. Switching Capacity	0.6 A 250 VAC, 50/60 Hz (2.4 A/Unit)
Max. Inrush Current	15 A (pulse width: 10 ms max.)
Min. Switching Capacity	50 mA 75 VAC
Leakage Current	1.5 mA (200 VAC) max.
Residual Voltage	1.6 VAC max.
ON Response Time	1 ms max.
OFF Response Time	1/2 of load frequency + 1 ms or less.
Number of Circuits	8 (8 points/common, 1 circuit)
Surge Protector	C.R Absorber + Surge Absorber
Fuses	5 A (1/common, 1 used)  The fuse cannot be replaced by the user.
Insulation Resistance	20 MΩ between the external terminals and the GR terminal (500 VDC)
Dielectric Strength	2,000 VAC between the external terminals and the GR terminal for 1 minute at a  leakage current of 10 mA max.
Internal Current Consumption	220 mA max.
Weight	150 g max.
Circuit Configuration	The signal names of the terminals are the device variable names.  The device variable names are the names that use "Jxx" as the device name.
External connection and  terminal-device variable  diagram	The signal names of the terminals are the device variable names.  The device variable names are the names that use "Jxx" as the device name.

* Terminal numbers A0 to A8 and B0 to B8 are used in the external connection and terminal-device variable diagrams. 
   They are not printed on the Units. 
Note: Although 16 I/O bits (1 word) are allocated, only 8 of these can be used for external I/O.

CJ1W-OD201 Transistor Output Unit (8 Points)

Name	8-point Transistor Output Unit with Terminal Block (Sinking Outputs)
Model	CJ1W-OD201
Rated Voltage	12 to 24 VDC
Operating Load Voltage Range	10.2 to 26.4 VDC
Maximum Load Current	2.0 A/point, 8.0 A/Unit
Maximum Inrush Current	10 A/point, 10 ms max.
Leakage Current	0.1 mA max.
Residual Voltage	1.5 V max.
ON Response Time	0.5 ms max.
OFF Response Time	1.0 ms max.
Insulation Resistance	20 MΩ between the external terminals and the GR terminal (100 VDC)
Dielectric Strength	1,000 VAC between the external terminals and the GR terminal for 1 minute at a  leakage current of 10 mA max.
Number of Circuits	8 (4 points/common, 2 circuits)
Internal Current Consumption	90 mA max.
Fuse	6.3 A (1/common, 2 used)  The fuse cannot be replaced by the user.
External Power Supply	12 to 24 VDC, 10 mA min.
Weight	110 g max.
Circuit Configuration	The signal names of the terminals are the device variable names.  The device variable names are the names that use "Jxx" as the device name.
External connection and  terminal-device variable  diagram	When wiring, pay careful attention to the polarity of the external power supply. The  load may operate incorrectly if the polarity is reversed.  The signal names of the terminals are the device variable names.  The device variable names are the names that use "Jxx" as the device name.

* Terminal numbers A0 to A8 and B0 to B8 are used in the external connection and terminal-device variable diagrams. 
    They are not printed on the Units. 
Note: Although 16 I/O bits (1 word) are allocated, only 8 of these can be used for external I/O.

CJ1W-OD203 Transistor Output Unit (8 Points)

Name	8-point Transistor Output Unit with Terminal Block (Sinking Outputs)
Model	CJ1W-OD203
Rated Voltage	12 to 24 VDC
Operating Load Voltage Range	10.2 to 26.4 VDC
Maximum Load Current	0.5 A/point, 4.0 A/Unit
Maximum Inrush Current	4.0 A/point, 10 ms max.
Leakage Current	0.1 mA max.
Residual Voltage	1.5 V max.
ON Response Time	0.1 ms max.
OFF Response Time	0.8 ms max.
Insulation Resistance	20 MΩ between the external terminals and the GR terminal (100 VDC)
Dielectric Strength	1,000 VAC between the external terminals and the GR terminal for 1 minute at a  leakage current of 10 mA max.
Number of Circuits	8 (8 points/common, 1 circuit)
Internal Current Consumption	100 mA max.
Fuse	None
External Power Supply	10.2 to 26.4 VDC, 20 mA min.
Weight	110 g max.
Circuit Configuration	The signal names of the terminals are the device variable names.  The device variable names are the names that use "Jxx" as the device name.
External connection and  terminal-device variable  diagram	When wiring, pay careful attention to the polarity of the external power supply. The  load may operate incorrectly if the polarity is reversed.  The signal names of the terminals are the device variable names.  The device variable names are the names that use "Jxx" as the device name.

* Terminal numbers A0 to A8 and B0 to B8 are used in the external connection and terminal-device variable diagrams. 
   They are not printed on the Units. 
Note: Although 16 I/O bits (1 word) are allocated, only 8 of these can be used for external I/O.

CJ1W-OD211 Transistor Output Unit (16 Points)

Name	16-point Transistor Output Unit with Terminal Block (Sinking Outputs)
Model	CJ1W-OD211
Rated Voltage	12 to 24 VDC
Operating Load Voltage Range	10.2 to 26.4 VDC
Maximum Load Current	0.5 A/point, 5.0 A/Unit
Maximum Inrush Current	4.0 A/point, 10 ms max.
Leakage Current	0.1 mA max.
Residual Voltage	1.5 V max.
ON Response Time	0.1 ms max.
OFF Response Time	0.8 ms max.
Insulation Resistance	20 MΩ between the external terminals and the GR terminal (100 VDC)
Dielectric Strength	1,000 VAC between the external terminals and the GR terminal for 1 minute at a  leakage current of 10 mA max.
Number of Circuits	16 (16 points/common, 1 circuit)
Internal Current Consumption	5 VDC 100 mA max.
Fuse	None
External Power Supply	10.2 to 26.4 VDC, 20 mA min.
Weight	110 g max.
Circuit Configuration	The signal names of the terminals are the device variable names.  The device variable names are the names that use "Jxx" as the device name.
External connection and  terminal-device variable  diagram	When wiring, pay careful attention to the polarity of the external power supply. The  load may operate incorrectly if the polarity is reversed.  The signal names of the terminals are the device variable names.  The device variable names are the names that use "Jxx" as the device name.

* Terminal numbers A0 to A8 and B0 to B8 are used in the external connection and terminal-device variable diagrams. 
    They are not printed on the Units.

CJ1W-OD213 Transistor Output Unit (16 Points)

Name	16-point Transistor Output Unit with Terminal Block (Sinking Outputs)
Model	CJ1W-OD213
Rated Voltage	24 VDC
Operating Load Voltage Range	20.4 to 26.4 VDC
Maximum Load Current	0.5 A/point, 5.0 A/Unit
Maximum Inrush Current	4.0 A/point, 10 ms max.
Leakage Current	0.1 mA max.
Residual Voltage	1.5 V max.
ON Response Time	15 μs max.
OFF Response Time	80 μs max.
Insulation Resistance	20 MΩ between the external terminals and the GR terminal (100 VDC)
Dielectric Strength	1,000 VAC between the external terminals and the GR terminal for 1 minute at a  leakage current of 10 mA max.
Number of Circuits	16 (16 points/common, 1 circuit)
Internal Current Consumption	5 VDC 150 mA max.
Fuse	None
External Power Supply	20.4 to 26.4 VDC, 55 mA min.
Weight	110 g max.
Circuit Configuration	The signal names of the terminals are the device variable names.  The device variable names are the names that use "Jxx" as the device name.
External connection and  terminal-device variable  diagram	When wiring, pay careful attention to the polarity of the external power supply. The  load may operate incorrectly if the polarity is reversed.  The signal names of the terminals are the device variable names.  The device variable names are the names that use "Jxx" as the device name.

* Terminal numbers A0 to A8 and B0 to B8 are used in the external connection and terminal-device variable diagrams. 
   They are not printed on the Units.

CJ1W-OD231 Transistor Output Unit (32 Points)

Name	32-point Transistor Output Unit with Fujitsu Connector (Sinking Outputs)
Model	CJ1W-OD231
Rated Voltage	12 to 24 VDC
Operating Load Voltage Range	10.2 to 26.4 VDC
Maximum Load Current	0.5 A/point, 2.0 A/common, 4.0 A/Unit
Maximum Inrush Current	4.0 A/point, 10 ms max.
Leakage Current	0.1 mA max.
Residual Voltage	1.5 V max.
ON Response Time	0.1 ms max.
OFF Response Time	0.8 ms max.
Insulation Resistance	20 MΩ between the external terminals and the GR terminal (100 VDC)
Dielectric Strength	1,000 VAC between the external terminals and the GR terminal for 1 minute at a  leakage current of 10 mA max.
Number of Circuits	32 (16 points/common, 2 circuits)
Internal Current Consumption	5 VDC 140 mA max.
Fuse	None
External Power Supply	10.2 to 26.4 VDC, 30 mA min.
Weight	70 g max.
Accessories	None
Circuit Configuration	The signal names of the terminals are the device variable names.  The device variable names are the names that use "Jxx" as the device name.
External connection and  terminal-device variable  diagram	When wiring, pay careful attention to the polarity of the external power supply. The  load may operate incorrectly if the polarity is reversed.  Be sure to wire both terminals A9 and A19 (COM0).  Be sure to wire both terminals B9 and B19 (COM1).  Be sure to wire both terminals A10 and A20 (+V).  Be sure to wire both terminals B10 and B20 (+V).  The signal names of the terminals are the device variable names.  The device variable names are the names that use "Jxx" as the device name.

CJ1W-OD233 Transistor Output Unit (32 Points)

Name	32-point Transistor Output Unit with MIL Connector (Sinking Outputs)
Model	CJ1W-OD233
Rated Voltage	12 to 24 VDC
Operating Load Voltage Range	10.2 to 26.4 VDC
Maximum Load Current	0.5 A/point, 2 A/common, 4 A/Unit
Maximum Inrush Current	4.0 A/point, 10 ms max.
Leakage Current	0.1 mA max.
Residual Voltage	1.5 V max.
ON Response Time	0.1 ms max.
OFF Response Time	0.8 ms max.
Insulation Resistance	20 MΩ between the external terminals and the GR terminal (100 VDC)
Dielectric Strength	1,000 VAC between the external terminals and the GR terminal for 1 minute at a  leakage current of 10 mA max.
Number of Circuits	32 (16 points/common, 2 circuits)
Internal Current Consumption	140 mA max.
Fuse	None
External Power Supply	12 to 24 VDC, 30 mA min.
Weight	70 g max.
Circuit Configuration	The signal names of the terminals are the device variable names.  The device variable names are the names that use "Jxx" as the device name.
External connection and  terminal-device variable  diagram	When wiring, pay careful attention to the polarity of the external power supply. The  load may operate incorrectly if the polarity is reversed.  Be sure to wire both terminals 23 and 24 (COM0).  Be sure to wire both terminals 3 and 4 (COM1).  Be sure to wire both terminals 21 and 22 (+V).  Be sure to wire both terminals 1 and 2 (+V).  The signal names of the terminals are the device variable names.  The device variable names are the names that use "Jxx" as the device name.

CJ1W-OD234 Transistor Output Unit (32 Points)

Name	32-point Transistor Output Unit with MIL Connector (Sinking Outputs)
Model	CJ1W-OD234
Rated Voltage	24 VDC
Operating Load Voltage Range	20.4 to 26.4 VDC
Maximum Load Current	0.5 A/point, 2 A/common, 4 A/Unit
Maximum Inrush Current	4.0 A/point, 10 ms max.
Leakage Current	0.1 mA max.
Residual Voltage	1.5 V max.
ON Response Time	15 μs max.
OFF Response Time	80 μs max.
Insulation Resistance	20 MΩ between the external terminals and the GR terminal (100 VDC)
Dielectric Strength	1,000 VAC between the external terminals and the GR terminal for 1 minute at a  leakage current of 10 mA max.
Number of Circuits	32 (16 points/common, 2 circuits)
Internal Current Consumption	220 mA max.
Fuse	None
External Power Supply	20.4 to 26.4 VDC, 110 mA min.
Weight	70 g max.
Circuit Configuration	The signal names of the terminals are the device variable names.  The device variable names are the names that use "Jxx" as the device name.
External connection and  terminal-device variable  diagram	When wiring, pay careful attention to the polarity of the external power supply. The  load may operate incorrectly if the polarity is reversed.  Be sure to wire both terminals 23 and 24 (COM0).  Be sure to wire both terminals 3 and 4 (COM1).  Be sure to wire both terminals 21 and 22 (+V).  Be sure to wire both terminals 1 and 2 (+V).  The signal names of the terminals are the device variable names.  The device variable names are the names that use "Jxx" as the device name.

CJ1W-OD261 Transistor Output Unit (64 Points)

Name	64-point Transistor Output Unit with Fujitsu Connectors (Sinking Outputs)
Model	CJ1W-OD261
Rated Voltage	12 to 24 VDC
Operating Load  Voltage Range	10.2 to 26.4 VDC
Maximum Load  Current	0.3 A/point, 1.6 A/common, 6.4 A/Unit
Maximum Inrush  Current	3.0 A/point, 10 ms max.
Leakage Current	0.1 mA max.
Residual Voltage	1.5 V max.
ON Response  Time	0.5 ms max.
OFF Response  Time	1.0 ms max.
Insulation  Resistance	20 MΩ between the external terminals and the GR terminal (100 VDC)
Dielectric  Strength	1,000 VAC between the external terminals and the GR terminal for 1 minute at a leakage current of  10 mA max.
Number of  Circuits	64 (16 points/common, 4 circuits)
Internal Current  Consumption	5 VDC, 170 mA max.
Fuse	None
External Power  Supply	10.2 to 26.4 VDC, 50 mA min.
Weight	110 g max.
Accessories	None
Circuit  Configuration	The signal names of the terminals are the device variable names.  The device variable names are the names that use "Jxx" as the device name.
External  connection  and terminal-  device variable  diagram	CN1	CN2
	When wiring, pay careful attention to the polarity  of the external power supply. The load may  operate incorrectly if the polarity is reversed.  Be sure to wire both terminals A9 and A19  (COM0) of CN1.  Be sure to wire both terminals B9 and B19  (COM1) of CN1.  Be sure to wire both terminals A10 and A20 (+V)  of CN1.  Be sure to wire both terminals B10 and B20 (+V)  of CN1.  The signal names of the terminals are the  device variable names.The device variable  names are the names that use "Jxx" as the  device name.	When wiring, pay careful attention to the polarity  of the external power supply. The load may  operate incorrectly if the polarity is reversed.  Be sure to wire both terminals A9 and A19  (COM2) of CN2.  Be sure to wire both terminals B9 and B19  (COM3) of CN2.  Be sure to wire both terminals A10 and A20 (+V)  of CN2.  Be sure to wire both terminals B10 and B20 (+V)  of CN2.  The signal names of the terminals are the  device variable names.The device variable  names are the names that use "Jxx" as the  device name.

CJ1W-OD263 Transistor Output Unit (64 Points)

Name	64-point Transistor Output Unit with MIL Connectors (Sinking Outputs)
Model	CJ1W-OD263
Rated Voltage	12 to 24 VDC
Operating Load  Voltage Range	10.2 to 26.4 VDC
Maximum Load  Current	0.3 A/point, 1.6 A/common, 6.4 A/Unit
Maximum Inrush  Current	3.0 A/point, 10 ms max.
Leakage Current	0.1 mA max.
Residual Voltage	1.5 V max.
ON Response  Time	0.5 ms max.
OFF Response  Time	1.0 ms max.
Insulation  Resistance	20 MΩ between the external terminals and the GR terminal (100 VDC)
Dielectric  Strength	1,000 VAC between the external terminals and the GR terminal for 1 minute at a leakage current of  10 mA max.
Number of  Circuits	64 (16 points/common, 4 circuits)
Internal Current  Consumption	170 mA max.
Fuse	None
External Power  Supply	12 to 24 VDC, 50 mA min.
Weight	110 g max.
Circuit  Configuration	The signal names of the terminals are the device variable names.  The device variable names are the names that use "Jxx" as the device name.
External  connection  and terminal-  device variable  diagram	CN1	CN2
	When wiring, pay careful attention to the polarity  of the external power supply. The load may  operate incorrectly if the polarity is reversed.  Be sure to wire both terminals 23 and 24 (COM0)  of CN1.  Be sure to wire both terminals 3 and 4 (COM1) of  CN1.  Be sure to wire both terminals 21 and 22 (+V) of  CN1.  Be sure to wire both terminals 1 and 2 (+V) of  CN1.  The signal names of the terminals are the  device variable names.The device variable  names are the names that use "Jxx" as the  device name.	When wiring, pay careful attention to the polarity  of the external power supply. The load may  operate incorrectly if the polarity is reversed.  Be sure to wire both terminals 23 and 24  (COM2) of CN2.  Be sure to wire both terminals 3 and 4 (COM3)  of CN2.  Be sure to wire both terminals 21 and 22 (+V) of  CN2.  Be sure to wire both terminals 1 and 2 (+V) of  CN2.  The signal names of the terminals are the  device variable names.The device variable  names are the names that use "Jxx" as the  device name.

CJ1W-OD202 Transistor Output Unit (8 Points)

Name	8-point Transistor Output Unit with Terminal Block (Sourcing Outputs)
Model	CJ1W-OD202
Rated Voltage	24 VDC
Operating Load Voltage  Range	20.4 to 26.4 VDC
Maximum Load Current	2 A/point, 8 A/Unit
Leakage Current	0.1 mA max.
Residual Voltage	1.5 V max.
ON Response Time	0.5 ms max.
OFF Response Time	1.0 ms max.
Load Short-circuit  Protection	Detection current: 6 A min.  Automatic restart after error clearance.
Line Disconnection  Detection	Detection current: 200 mA
Insulation Resistance	20 MΩ between the external terminals and the GR terminal (100 VDC)
Dielectric Strength	1,000 VAC between the external terminals and the GR terminal for 1 minute at a leakage  current of 10 mA max.
Number of Circuits	8 (4 points/common, 2 circuits)
Internal Current  Consumption	110 mA max.
Fuse	None
External Power Supply	24 VDC, 50 mA min.
Weight	120 g max.
Circuit Configuration	When overcurrent or line disconnection is detected, the ERR indicator will light, and the  corresponding bit (two points per bit) in the Basic I/O Unit Information Area (A050 to  A069) will change to TRUE.  The signal names of the terminals are the device variable names.  The device variable names are the names that use "Jxx" as the device name.
External connection and  terminal-device variable  diagram	When wiring, pay careful attention to the polarity of the external power supply. The load  may operate incorrectly if the polarity is reversed.  The signal names of the terminals are the device variable names.  The device variable names are the names that use "Jxx" as the device name.

* Terminal numbers A0 to A8 and B0 to B8 are used in the external connection and terminal-device variable diagrams. 
   They are not printed on the Units. 
Note: Although 16 I/O bits (1 word) are allocated, only 8 of these can be used for external I/O.

CJ1W-OD204 Transistor Output Unit (8 Points)

Name	8-point Transistor Output Unit with Terminal Block (Sourcing Outputs)
Model	CJ1W-OD204
Rated Voltage	24 VDC
Operating Load Voltage  Range	20.4 to 26.4 VDC
Maximum Load Current	0.5 A/point, 4.0 A/Unit
Leakage Current	0.1 mA max.
Residual Voltage	1.5 V max.
ON Response Time	0.5 ms max.
OFF Response Time	1.0 ms max.
Load Short-circuit  Protection	Detection current: 0.7 to 2.5 A  Automatic restart after error clearance.
Insulation Resistance	20 MΩ between the external terminals and the GR terminal (100 VDC)
Dielectric Strength	1,000 VAC between the external terminals and the GR terminal for 1 minute at a leakage  current of 10 mA max.
Number of Circuits	8 (8 points/common, 1 circuit)
Internal Current  Consumption	5 VDC, 100 mA max.
Fuse	None
External Power Supply	20.4 to 26.4 VDC, 40 mA min.
Weight	120 g max.
Circuit Configuration	When overcurrent is detected, the ERR indicator will light, and the corresponding bit in the  Basic I/O Unit Information Area (A050 to A069) will change to TRUE.  The signal names of the terminals are the device variable names.  The device variable names are the names that use "Jxx" as the device name.
External connection and  terminal-device variable  diagram	When wiring, pay careful attention to the polarity of the external power supply. The load  may operate incorrectly if the polarity is reversed.  The signal names of the terminals are the device variable names.  The device variable names are the names that use "Jxx" as the device name.

* Terminal numbers A0 to A8 and B0 to B8 are used in the external connection and terminal-device variable diagrams. 
    They are not printed on the Units. 
Note: Although 16 I/O bits (1 word) are allocated, only 8 of these can be used for external I/O.

CJ1W-OD212 Transistor Output Unit (16 Points)

Name	16-point Transistor Output Unit with Terminal Block (Sourcing Outputs)
Model	CJ1W-OD212
Rated Voltage	24 VDC
Operating Load Voltage  Range	20.4 to 26.4 VDC
Maximum Load Current	0.5 A/point, 5.0 A/Unit
Maximum Inrush Current	0.1 mA max.
Leakage Current	1.5 V max.
ON Response Time	0.5 ms max.
OFF Response Time	1.0 ms max.
Load Short-circuit  Protection	Detection current: 0.7 to 2.5 A  Automatic restart after error clearance.
Insulation Resistance	20 MΩ between the external terminals and the GR terminal (100 VDC)
Dielectric Strength	1,000 VAC between the external terminals and the GR terminal for 1 minute at a leakage  current of 10 mA max.
Number of Circuits	16 (16 points/common, 1 circuit)
Internal Current  Consumption	5 VDC, 100 mA max.
External Power Supply	20.4 to 26.4 VDC, 40 mA min.
Weight	120 g max.
Circuit Configuration	When overcurrent is detected, the ERR indicator will light, and the corresponding bit in the  Basic I/O Unit Information Area (A050 to A069) will change to TRUE.  The signal names of the terminals are the device variable names.  The device variable names are the names that use "Jxx" as the device name.
External connection and  terminal-device variable  diagram	When wiring, pay careful attention to the polarity of the external power supply. The load may  operate incorrectly if the polarity is reversed.  The signal names of the terminals are the device variable names.  The device variable names are the names that use "Jxx" as the device name.

* Terminal numbers A0 to A8 and B0 to B8 are used in the external connection and terminal-device variable diagrams. 
   They are not printed on the Units.

CJ1W-OD232 Transistor Output Unit (32 Points)

Name	32-point Transistor Output Unit with MIL Connector (Sourcing Outputs)
Model	CJ1W-OD232
Rated Voltage	24 VDC
Operating Load Voltage  Range	20.4 to 26.4 VDC
Maximum Load Current	0.5 A/point, 2.0 A/common, 4.0 A/Unit
Leakage Current	0.1 mA max.
Residual Voltage	1.5 V max.
ON Response Time	0.5 ms max.
OFF Response Time	1.0 ms max.
Load Short-circuit  Protection	Detection current: 0.7 to 2.5 A  Automatic restart after error clearance.
Insulation Resistance	20 MΩ between the external terminals and the GR terminal (100 VDC)
Dielectric Strength	1,000 VAC between the external terminals and the GR terminal for 1 minute at a leakage  current of 10 mA max.
Number of Circuits	32 (16 points/common, 2 circuits)
Internal Current  Consumption	5 VDC 150 mA max.
External Power Supply	20.4 to 26.4 VDC, 70 mA min.
Weight	80 g max.
Accessories	None
Circuit Configuration	When overcurrent is detected, the ERR indicator will light, and the corresponding bit (bit  allocated for each common) in the Basic I/O Unit Information Area (A050 to A069) will  change to TRUE.  The signal names of the terminals are the device variable names.  The device variable names are the names that use "Jxx" as the device name.
External connection and  terminal-device variable  diagram	When wiring, pay careful attention to the polarity of the external power supply. The load may  operate incorrectly if the polarity is reversed.  Be sure to wire both terminals 21 and 22 (COM0 (+V)).  Be sure to wire both terminals 1 and 2 (COM1 (+V)).  Be sure to wire both terminals 3 and 4 (0 V).  Be sure to wire both terminals 23 and 24 (0 V).  The signal names of the terminals are the device variable names.  The device variable names are the names that use "Jxx" as the device name.

CJ1W-OD262 Transistor Output Unit (64 Points)

Name	64-point Transistor Output Unit with MIL Connectors (Sourcing Outputs)
Model	CJ1W-OD262
Rated Voltage	12 to 24 VDC
Operating Load  Voltage Range	10.2 to 26.4 VDC
Maximum Load  Current	0.3 A/point, 1.6 A/common, 6.4 A/Unit
Maximum Inrush  Current	3.0 A/point, 10 ms max.
Leakage Current	0.1 mA max.
Residual Voltage	1.5 V max.
ON Response  Time	0.5 ms max.
OFF Response  Time	1.0 ms max.
Insulation  Resistance	20 MΩ between the external terminals and the GR terminal (100 VDC)
Dielectric  Strength	1,000 VAC between the external terminals and the GR terminal for 1 minute at a leakage current  of 10 mA max.
Number of  Circuits	64 (16 points/common, 4 circuits)
Internal Current  Consumption	170 mA max. (5 VDC)
Fuse	None
External Power  Supply	10.2 to 26.4 VDC, 50 mA min.
Weight	110 g max.
Accessories	None
Circuit  Configuration	The signal names of the terminals are the device variable names.  The device variable names are the names that use "Jxx" as the device name.
External  connection  and terminal-  device variable  diagram	CN1	CN2
	When wiring, pay careful attention to the polarity  of the external power supply. The load may  operate incorrectly if the polarity is reversed.  Be sure to wire both terminals 21 and 22 (COM0  (+V)) of CN1.  Be sure to wire both terminals 1 and 2 (COM1  (+V)) of CN1.  Be sure to wire both terminals 23 and 24 (0 V)  of CN1.  Be sure to wire both terminals 3 and 4 (0 V) of  CN1.  The signal names of the terminals are the device  variable names.The device variable names are  the names that use "Jxx" as the device name.	When wiring, pay careful attention to the polarity  of the external power supply. The load may  operate incorrectly if the polarity is reversed.  Be sure to wire both terminals 21 and 22  (COM2 (+V)) of CN2.  Be sure to wire both terminals 1 and 2 (COM3  (+V)) of CN2.  Be sure to wire both terminals 23 and 24 (0 V)  of CN2.  Be sure to wire both terminals 3 and 4 (0 V) of  CN2.  The signal names of the terminals are the  device variable names.The device variable  names are the names that use "Jxx" as the  device name.

Bit Allocations for Output Unit

8-point Output Unit

Allocated CIO word		Signal name (CJ/NJ)
CIO	Bit
Wd m (Output)	00	OUT0/Jxx_Ch1_Out00
	01	OUT1/Jxx_Ch1_Out01
	:	:
	06	OUT6/Jxx_Ch1_Out06
	07	OUT7/Jxx_Ch1_Out07
	08	-
	09	-
	:	:
	14	-
	15	-

16-point Output Unit

Allocated CIO word		Signal name (CJ/NJ)
CIO	Bit
Wd m (Output)	00	OUT0/Jxx_Ch1_Out00
	01	OUT1/Jxx_Ch1_Out01
	:	:
	14	OUT14/Jxx_Ch1_Out14
	15	OUT15/Jxx_Ch1_Out15

32-point Output Unit

Allocated CIO word		Signal name (CJ/NJ)
CIO	Bit
Wd m (Output)	00	OUT0/Jxx_Ch1_Out00
	01	OUT1/Jxx_Ch1_Out01
	:	:
	14	OUT14/Jxx_Ch1_Out14
	15	OUT15/Jxx_Ch1_Out15
Wd m+1 (Output)	00	OUT0/Jxx_Ch2_Out00
	01	OUT1/Jxx_Ch2_Out01
	:	:
	14	OUT14/Jxx_Ch2_Out14
	15	OUT15/Jxx_Ch2_Out15

64-point Output Unit

Allocated CIO word		Signal name (CJ/NJ)
CIO	Bit
Wd m (Output)	00	OUT0/Jxx_Ch1_Out00
	01	OUT1/Jxx_Ch1_Out01
	:	:
	14	OUT14/Jxx_Ch1_Out14
	15	OUT15/Jxx_Ch1_Out15
Wd m+1 (Output)	00	OUT0/Jxx_Ch2_Out00
	01	OUT1/Jxx_Ch2_Out01
	:	:
	14	OUT14/Jxx_Ch2_Out14
	15	OUT15/Jxx_Ch2_Out15
Wd m+2 (Output)	00	OUT0/Jxx_Ch3_Out00
	01	OUT1/Jxx_Ch3_Out01
	:	:
	14	OUT14/Jxx_Ch3_Out14
	15	OUT15/Jxx_Ch3_Out15
Wd m+3 (Output)	00	OUT0/Jxx_Ch4_Out00
	01	OUT1/Jxx_Ch4_Out01
	:	:
	14	OUT14/Jxx_Ch4_Out14
	15	OUT15/Jxx_Ch4_Out15